If your wipers only work on continuous settings, first check whether the setting you expect to provide timed wipes is actually rain-sensing AUTO mode. If manual intermittent wiping fails, the switch input, delay control, wiring, or motor’s park circuit needs diagnosis. For drivers in Decatur, Texas, a clear record of which modes work helps a technician narrow the problem.
Continuous wiping shows that the motor can move the blades. It does not prove that every function inside the motor assembly or its controls is healthy. That is why this symptom alone does not justify replacing the motor, switch, or a presumed intermittent relay.
Check manual intermittent versus rain-sensing AUTO
Look up the wiper controls in the owner’s manual for your vehicle’s year and equipment. Confirm what the INT or AUTO position does and what the adjustment ring controls.
- Manual intermittent: The adjustment changes the pause between wipes.
- Rain-sensing AUTO: The adjustment changes sensitivity to water, rather than selecting a fixed pause.
Ford’s wiper guidance illustrates the difference: on the equipped vehicles it describes, higher sensitivity responds to less water, while lower sensitivity requires more. A pause without another wipe therefore may reflect the selected automatic setting rather than failed delay control.
Some vehicles let you disable rain sensing in a vehicle-settings menu and use manual intermittent wiping instead. Ford describes that option, but the menu and available modes depend on the vehicle. Follow your own manual rather than assuming the same sequence applies to every car or pickup.
If your vehicle supports that comparison, note whether manual intermittent works with rain sensing disabled. That gives the technician a more specific complaint than “the slow setting does nothing.”
Record the mode shown in the menu along with the position of the lever or dial. For example, “AUTO selected, low sensitivity, continuous low and high both work” tells the technician what you actually tried. If the manual does not describe a timed mode with rain sensing disabled, report that too. Avoid treating a control position as a failed timer until you have confirmed that it is supposed to provide timed wiping.
Record what works and where the blades stop
Make observations while parked, with the windshield wet and your hands clear of the wipers. There is no need to disassemble the switch or probe wiring to provide useful information.
Write down:
- Whether both continuous low and high speeds work.
- Whether every intermittent dial position fails or only certain positions.
- Whether selecting intermittent produces no movement, one sweep and then nothing, or repeated sweeps with an unexpected pause.
- Whether the blades return to their usual resting position after you switch continuous wiping off.
- Whether single-wipe and washer-triggered wiping work, if equipped.
- Whether the symptom began after windshield replacement or electrical work.
A short written description can keep the symptoms clear: “Low and high work; INT wipes once at every dial position; switching off returns the blades to the bottom.” Another useful report would be: “Manual delay works, but AUTO does not respond as expected.” These are examples of how to describe the behavior, not diagnoses of a particular component.
Bring the vehicle year, make, model, and the control settings you used. If the behavior changes between checks, describe both results instead of choosing the one that seems most typical. Do not try to recreate the fault while driving just to collect a better description.
Recent work is background information, not proof of the cause. Likewise, blades stopping partway across the glass is a clue to report, not a reason to order a motor yourself.
Parking behavior deserves attention. Thor Motor Coach’s troubleshooting guide for its listed models checks whether the wipers run and park when investigating an intermittent-only failure. It then distinguishes controller trouble from park-circuit and motor park-switch problems. Your vehicle needs its own test procedure, but that example explains why “it still wipes on low” does not settle the diagnosis.
What electrical diagnosis should establish before parts replacement
Decatur Tires lists electrical diagnosis and repair, along with windshield wiper installation and maintenance. For this complaint, the repair decision should follow the vehicle’s wiring diagram and service tests.
The questions to resolve are:
- Does the system receive the selected switch command? Where supported, scan-tool data can help verify that the selected position is being recognized.
- Are the relevant connections and circuits intact? Check the applicable connectors, power supply, grounds, and wiring before condemning a component.
- Does the parking function behave correctly? Test the relevant park circuit or feedback according to the vehicle’s design.
- Which component fails the prescribed tests? Depending on the system, the evidence may point toward a switch, delay controller, relay, wiring fault, or motor assembly.
FCA’s published guidance for a different wiper-speed failure illustrates the method: verify switch-position input, then inspect the relevant connector terminals. That case also had no diagnostic trouble codes. It does not identify the cause of your intermittent problem; it shows why an empty code scan is not a complete electrical diagnosis.
Before approving a replacement, ask the technician to explain the distinction between the symptom and the test result. “Intermittent does not work” describes the complaint. A finding that the selected command is not being received, or that a tested circuit fails the vehicle’s specified check, gives a basis for the repair. The explanation should identify what was checked and how that finding supports the recommendation.
A part named in another vehicle’s troubleshooting guide is not a shopping list for yours. Ask whether the proposed repair follows the service information for your particular vehicle, especially when a motor assembly or control module is being recommended.
Include any other control symptoms in that history, such as a turn signal blinking fast, without assuming they share a cause with the wiper problem.
If your intermittent wipers are not working, ask which test supports the proposed part or wiring repair. After repair, verification should include the delay settings, continuous speeds, and return to park.



